- Eastwood Original DIY Powder Coating Gun Starter Kit
Eastwood Original DIY Powder Coating Gun Starter Kit
This kit comes with the items you need to start powder coating. Just add compressed air and a curing oven or lamp.
Eastwood Original DIY Powder Coating Gun
The Original HotCoat Powder-Coating Gun brings the benefits of powder coating right to your home garage or shop.
- Coat and cure in under an hour!
- Easy to apply
- Extremely durable finish
- Quick color changes
- 11,000-volt output
This innovative, inexpensive powder-coat gun helps you do a professional-looking powder coating job right at home. All you need to add are a compressed air source (5-10psi) from a portable tank with a regulator or a compressor), a dedicated electric oven or toaster oven, and powder colors.
Why powder coat? Because it gives you one of the most economical, color-durable, and longest-lasting finishes available. You'll find powder-coated surfaces are far more resistant to chipping, scratches, fading, and wear than other finishes, and the color selection is virtually unlimited, with high and low gloss, metallic, and clear finishes available. And thanks to the UV resistance of many of the powders, colors stay bright and vibrant longer. Texture selections range from smooth surfaces to a wrinkled or matte finish, plus rough textures designed for hiding surface imperfections.
One 8-oz. bottle of powder covers the same area as 2-3 cans of spray paint, and clean-up is easy, since you can simply sweep-up the oversprayed powder. Contains no environmentally harmful solvents. HotCoat powder coating requires a 5-10psi compressed air source and dedicated electric oven The accessories kit comes with the items you need to start powder coating except for a compressor and curing oven or lamp. The high temperature tape and silicone plugs make it easy to mask areas you do not want to get powder on. The safety wire is great for hanging parts on your powder coating rack or oven. This kit also comes with an in-line air filter to keep contaminates out of your gun and powder. Also included is an 8 oz. bottle of high gloss black powder and extra storage bottles.
Powder Coating Accessory Kit
The accessories kit comes with the items you need to start powder coating except for a compressor and curing oven or lamp. The high temperature tape and silicone plugs make it easy to mask areas you do not want to get powder on. The safety wire is great for hanging parts on your powder coating rack or oven. This kit also comes with an in-line air filter to keep contaminates out of your gun and powder. Also included is an 8 oz. bottle of high gloss black powder and extra storage bottles.
- 11671A Eastwood DIY Powder Coating Gun
- 1/2" High Temperature Fiberglass Masking Tape
- (30) High Temp Silicone Plugs Assortment
- 1 lb spool Safety Wire .041"
- 8 ounces High Gloss Black Powder
- (3) 8 ounce plastic bottles & lids
- Disposable In Line Air Filter
Use a disposable dust mask when handling or applying powder. Powder, like common flour, can be explosive when suspended in the air in high concentrations. To minimize any explosion risk, sweep up—do not vacuum—powder from the floor. Cure powder in a well-ventilated area. The urethane powders we sell liberate a very minute amount of isocyanates when the powder flows out. This usually occurs about 3-5 minutes after the part is placed in the oven to bake. Wear a respirator with fresh filter cartridges when curing or inspecting flow-out progress.
Click here to see safety products
(Q) How long does the baking process take?
(A) For improved flow out (less "orange peel"), bake coated parts at 500 degrees F until powder flows out (about 3-4 minutes for light sheet metal parts), then turn down the heat to 400 degrees F for a full 15 minutes.
(Q) What are the electrical requirements?
(A) This HotCoat Gun requires 110-125VAC, 2 amps at 50-60 Hz. Can be used with a voltage transformer such as 220-240VAC to 110-125VAC as long as the transformer can handle 2 amps.
Questions & Answers