Eastwood Pro Street Red 3:1 Single Stage Paint

Item #50379 ZP Pro Street Red

Eastwood Pro Street Red 3:1 Single Stage Paint
A medium shaded red that features warm under tones compared with the other solid reds in the Eastwood color lineup.

EW Pro Street Red 3:1 SS Urethane 96oz

Item #50218ZP

- +
Quantity: close

In stock

Eastwood Urethane Activator 32oz med temp less 80F

Item #21856ZP

- +
Quantity: close

In stock

Eastwood Single Stage Urethane Slow Activator Quart 80 Degrees F and above Mix 3:1

Item #21853ZP

- +
Quantity: close

In stock

Eastwood Zero VOC Urethane Reducer Quart

Item #50104ZP

Special Price $17.97

Regular Price: $18.99

Save: $1.02

- +
Quantity: close


Total $0


Find the right balance between being a fireball and taking it easy with this single-stage red auto paint that's easy to apply. Eastwood Pro Street Red 3:1 is a medium-shaded red that features warm undertones compared with the other solid reds in the Eastwood color lineup. It’s an excellent way to refinish classic cars, modern vehicles and custom hot rods as either the final coat or a base for pinstriping and other personalized effects. You can also use this urethane paint with a clear coat for extra shine and protection.

Our premium single-stage acrylic urethane topcoat provides exceptional long-lasting beauty and durability. The premium 2-component topcoat system is blended with top-quality raw materials and advanced composition coatings technology that’s superior to acrylic, alkyd and lacquer coatings. Eastwood single-stage urethane paints hold their gloss longer and won't yellow even after extended exposure to UV rays. The coating also resists chipping and chemical stains to further improve performance.

Order Eastwood Pro Street Single Stage Red Paint today with either the standard urethane activator or a special slow activator formulated for temperatures above 80 degrees Fahrenheit. You can also add a reducer to thin the paint perfectly for your HVLP spray gun. Call, email or visit the Eastwood Garage for expert DIY painting advice.

  • Catalyzed urethane for unsurpassed durability
  • Highly resistant to UV rays, chemicals, chips
  • Makes 1 sprayable gallon when mixed 3:1 with a required activator
  • Approximate coverage: 125 SQ FT
  • Max Temperature: Paint will handle up to 300 degrees without delamination, but color shift may occur, so it should not be used in a high heat setting
  • Made in the USA


Thoroughly mix three parts single-stage urethane paint with one part Activator. No additional reduction is required but can be used as needed. Use caution in mixing materials as Eastwood’s single-stage urethane paint may begin to gel after approximately two hours (at 70 °F).

HVLP Gun: Fluid Tip 1.3-1.5 mm Inlet Spray Pressure 25-30 psi
Conventional Gravity: Fluid Tip 1.3-1.6 mm Inlet Spray Pressure 45-50 psi
Conventional Siphon: Fluid Tip: 1.4-1.8 mm Inlet Spray Pressure 45-50 psi

Apply single-stage urethane paints in two to three medium wet coats as necessary to achieve sufficient coverage, allowing ten minute flash between coats. Additional coats may be necessary to achieve total coverage for some metallic colors. A final “fog coat” may be applied with metallic colors to help set an even flake pattern and /or adjust flake orientation. A dry film thickness of approximately 2 mil is recommended. Paint should be dust free within 10-15 minutes and tack-free within one hour (at 70 °F). Re-coat anytime after the previous coat has flashed, or before 18 hours. After 18 hours, paint should be abraded prior to re-coating for proper adhesion purposes.

This urethane paint may be applied as a stand-alone single-stage system, or in combination with Eastwood’s High Solids Urethane Clear as a basecoat/clearcoat system. Additionally, Urethane Clear may be integrated into Urethane color. When combining the two systems, be sure to activate each side (the paint and the clear) separately, with their own activators at the correct mix ratios, before blending.

When used as a Single-Stage Urethane Paint, this coating may be wet-sanded and polished for increased depth and gloss like any other urethane topcoat. Care should be taken when lightly cutting metallic colors to prevent disturbing aluminum flake.


Always wear proper eye, skin and respiratory protection. Always paint in a well-ventilated area away from sparks and open flame. Consult MSDS and product data sheets for proper safety precautions.


(Q) Do I need a clear?
(A) No, but you should use a clearcoat over metallics.

(Q) How much paint do I need?
(A) Typically one gallon per car. If you are also painting jambs, under the hood, or the trunk, use 2 gallons. For large cars and pickup trucks, use 2 gallons. Number of coats, prep and application methods will affect the amount of paint required.

Eastwood Offers Free Lifetime Technical Support

Click here for product SDS information

Attention California Residents - Proposition 65

Proposition 65 Warning WARNING - Cancer and Reproductive Harm - www.P65Warnings.ca.gov


Customer Reviews

Questions & Answers