Columbus Day Sale
Scroll Compressor
  • Home
  • Eastwood Brush on Seam Sealer
Eastwood Brush on Seam Sealer is rated 4.5 out of 5 by 56.
Rated 5 out of 5 by from SEAM SEALER It tends to dry up the brush you use pretty fast so you might need more than one brush to use while you applied it on. Takes about a week to cure.
Date published: 2019-10-02
Rated 5 out of 5 by from Great Seam Sealer. This is agreat seam sealer. Very easy to use. Dries fast, no mess.
Date published: 2019-03-03
Rated 5 out of 5 by from Exactly what I needed I made some difficult rust repairs where my firewall meets the windshield cowl. I was concerned about pinholes in the welds and to a bit lesser extend the aesthetics of the repair. With that and the 40 year old cab was never really being well sealed in this area, I wanted to do better. I actually purchased this for some of the external firewall repairs and intended on purchasing the 2k seam sealer for the coal area but after working with it, this stuff seemed to ‘level’ well enough I gave it a go. I masked off the cowl slots and applied with some acid brushes. I don’t think I could have gotten a better result. Water will now flow across the cowl and down the side of the cab where it should rather than through the seams and down the firewall.
Date published: 2019-03-03
  • y_2019, m_10, d_12, h_24
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_56
  • loc_en_US, sid_51657ZP, prod, sort_[SortEntry(order=RATING, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Can this seam sealer be applied to bare metal that has been treated with a zinc containing metal prep?

Asked by: Giacomo
Yes it should not be an issue applying this Seam sealer over top for the application in reference.
Answered by: Kelly H
Date published: 2019-10-09

What can I use over original seam sealer to cover up cracks due to age

Asked by: Mark
Technically you can apply new over old but best results always would be to remove as much of the old as possible and start fresh. Here is a link to an article written by us in the bast which describes the best uses for the seam sealers we offer: https://garage.eastwood.com/eastwood-chatter/which-seam-sealer-and-when-to-use/
Answered by: Kelly H
Date published: 2019-08-25

If the sealer dries so quickly, is leaving the can open a problem when applying? Can it be thinned out if needed using.....?

Asked by: tojoII
The Seam Sealer will air dry in the 1 hour, the pot life, "in the can" will take a lot longer to skin over. You can smooth out the seam sealer with some Pre and using your finger with a glove on it, to work it into the shape that you need.
Answered by: Bob G
Date published: 2019-08-08

Can you use this to fill a 1/4 inch gap along the fire wall and cowl area?

Asked by: Deeredroper
This product is not designed to fill a gap without a backer. You would not want to surpass 1/4 inch thick.
Answered by: SeanW
Date published: 2019-06-20

would this be good too use on the fiberglass hi top. on a van. that has stress cracks from being 32 years old or what would you recommend.ty

Asked by: campervan
The USC Flexible Glaze would be a better product for your application. Item #16214Z https://www.eastwood.com/usc-garage-flexible-glaze-77704-with-hardener.html
Answered by: Bob G
Date published: 2019-04-28

Can this be applied over Eastwood Weld-through primer or EDP ?

Asked by: James
Yes this would be bale to be applied over the Weld Through Primer.
Answered by: Kelly H
Date published: 2019-02-12

When applying to underside of vehicle will the product sag or is it thick enough to not. I'm replacing floor pans and I don't have access to a rotisserie.

Asked by: Dan1
The Brush on Seam Sealer will not sag. It would be a great product for you application.
Answered by: Bob G
Date published: 2019-04-29

Can I use seam sealer over first primer coat?

Asked by: Kevin
This product need to be applied directly to metal.
Answered by: Dakota W
Date published: 2019-04-20
  • y_2019, m_10, d_12, h_17CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.13
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_33
  • loc_en_US, sid_51657ZP, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Eastwood Brush on Seam Sealer

Eastwood Brush on Seam Sealer

Item #51657ZP Brand: Eastwood

Seals cracks, crevices and body
seams, plus waterproofs and insulates
Quantity:
Quantity: close

In stock

Only $35.99

Sale $30.97

 

< Back

Details

After stripping a car or repairing a panel you should replace the seam sealer to protect your work from the elements.

  • Flexible - Will not shrink, harden or crack
  • Seals cracks, crevices and body seams
  • Paintable in 30 minutes
  • Waterproofs and insulates

Eastwood's Brush-On Seam Sealer leaves a factory-like finish and will not crack, harden or sag. Seals cracks, crevices and body seams as well as waterproofs and insulates. Tack dries in 15 minutes and air dries in 1hour. Remains flexible. Gray in color. Can be painted in 30 minutes.

Can be used on:

  • Firewall
  • Trunk seams
  • Fender extensions
  • Tail light openings
  • Floor pans
  • Many other areas

More info...
< Back

About Eastwood Brush on Seam Sealer

After stripping a car or repairing a panel you should replace the seam sealer to protect your work from the elements. Eastwood's Brush-On Seam Sealer leaves a factory-like finish and will not crack, harden or sag. Seals cracks, crevices and body seams as well as waterproofs and insulates. Tack dries in 15 minutes and air dries in 1hour. Remains flexible. Charcoal in color. Can be painted in 40 minutes. Use on firewall and trunk seams, fender extensions, tail light openings, etc. Eastwood also offers also stock Black (51655ZZ) or Beige (51656Z) and 2-component self-leveling epoxy cartridge (51653Z) to duplicate OE

Does not contain synthetic butyl rubber, nor any butyl


Contents

30.4-fl.-oz. (1.9 pt.)


Safety

always wear eye, skin and respiratory protection when working with chemicals consult MSDS for proper safety warnings


Warranty

Made in Canada


Application

Clean surface with Eastwood's PRE painting prep (10041Z) Apply a bead using a brush or finger. Tack dries in 15 minutes Paintable in 30-45 minutes Clean excess with PRE

Operation Temperature is between -4 degrees F to 158 degrees F.


Accessories

Eastwood PRE Painting Prep
Eastwood Flexible Strip Caulk
Eastwood Self-Etch Primer Gray


Eastwood Offers Free Lifetime Technical Support


Click here for product SDS information


Attention California Residents - Proposition 65


Proposition 65 Warning WARNING - Cancer and Reproductive Harm - www.P65Warnings.ca.gov






< Back

Customer Reviews

< Back

Questions & Answers

Customers also viewed: