- EW Contour Polyester Primer Surfacer Qt
EW Contour Polyester Primer Surfacer Qt
excellent base for any paint system
Contour™ Sprayable High-Build Primer/Surfacer serves as an excellent base for any paint system
- High-Build With Excellent Filling Capabilities
- Easy To Sand With No Shrinkage
- Excellent Adhesion To Metals, Fiberglass, and Body Fillers
- Includes hardener
2-component polyester primer/surfacer has excellent filling characteristics and superior adhesion to steel, aluminum, fiberglass, SMC, OE finishes, self-etching primers and body fillers.
About EW Contour Polyester Primer Surfacer Qt
Eastwood Sprayable Polyester Primer-Surfacer is a 2-component high build sprayable body filler that serves as an excellent base for any paint system. It has excellent filling characteristics and superior adhesion to steel, aluminum, fiberglass, SMC, OE Finishes, self Etching Primers and body fillers. Its high solids and high build formula allows you to achieve a laser straight surface prior to painting. Includes catalyst.
Primer: 32 Fl Ounces/ 946mL Catalyst: 2 oz/ 60g
1. Surface must be clean and free of wax, grease and debris. Use Eastwood’s PRE Painting Prep to remove all contaminants.
2. Sand/abrade surface
A. Body Filler & Putty: Rough sand with 80 grit, then 180-220 and featheredge with 320 grit
B. Untreated Steel, Galvanized and Aluminum: Sand with 80-180 grit
C. Painted Surfaces: Sand and featheredge using 80, 180 ,220 and finish with 320 grit.
3. Completely final sand surface with 320-400 grit paper and re-clean with PRE Painting Prep
MIX: 5% by weight Click here to view mix ratio chart
SPRAY GUN & APPLICATION RECOMMENDATIONS:
1.8mm to 2.5mm Fluid Tip Size, 35 to 40 PSI
Apply two or three medium wet coats as needed. Heavy wet coats should NOT be applied.
Dry spray may be removed be for recoating. Allow 90 minutes dry time before sanding at 68°F (20°C). Finish with 220 grit followed by 320-400 grit
DRY TIMES AT 68°F (20°C)
Flash: 5-10 minutes
To Sand: 90 minutes, over self etching primer: 4-6 hours
To Topcoat: 90 minutes, over self-etching primer: 4-6 hours
Force Dry: Purge 10 minutes, Bake: 30 minutes at 140°F (60°C)
Pot Life: 30 minutes at 68°F (20°C). If needed add 5-10% acetone to extend pot life.
Clean equipment with lacquer thinner immediately after use. This product is not meant for use below 60°F (16°C), dry time and performance will be dramatically affected.
CAUTION: DO NOT return catalyzed material back into can. To avoid contamination, seal lid tightly after each use. Store in a cool dry place.
Always wear eye, skin and resp[oratory protection when using this product always apply in a well ventilated area. consult MSDS and product label for specific safety warnings
Made in Canada to Eastwood's strict specifications and quality standards
Surface must be clean and free of wax, grease and debris. Body Filler & Putty: Rough sand w/80 grit, then 180-220, featheredge w/320 Painted Surfaces: Sand and featheredge using 80, 180 ,220 and finish w/320 Gun requirements: 1.8mm to 2.5mm Fluid Tip Size, 35 to 45 PSI Apply 2-3 medium wet coats. 90 min dry time @ 68Â°F finish with 220 and final with 320-400 grit.
Questions & Answers
Customers also viewed:
Save clean-up time, money: 100 tear- off mixing sheets on masonite boardOnly $19.99
Sands all types of flat and contoured surfaces; use wet or dryOnly $59.99
Stronger-than-it-looks portable stand holds up to 750 lbs.!Only $29.99