• Home
  • Eastwood Heat and Sound Barrier Coating 1.5 Gallon Kit
Eastwood Heat and Sound Barrier Coating 1.5 Gallon Kit is rated 3.1 out of 5 by 7.
Rated 5 out of 5 by from Very Happy Professional restoration shop. First time using this product as per customer request. We normally use Eastwood X Mat but customer wanted a spray down heat and sound. We are very happy with the way it applied and sprayed. 3 coats over bare steel brand new floors and seam sealer. It laid nice and adhered well. Cant speak for sound and heat. Its not our car.
Date published: 2018-03-13
Rated 5 out of 5 by from Sound and heat I have not used as of yet but like that I can kill two birds with one stone
Date published: 2016-09-19
Rated 5 out of 5 by from Heat and sound barrier kit I cannot attest to the claims of Heat or Sound qualities as of yet. (i am still in the process of building my car). I mainly wanted to use this as an undercoating to make sure that all of my efforts of replacing floor pans and rusted out areas did not go in vane. it went on very nicely and sealed the floor much better than I had hoped. I will use this product again on the inside of the vehicle.
Date published: 2015-12-31
  • y_2018, m_4, d_18, h_11
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_7
  • loc_en_US, sid_15632ZP, prod, sort_[SortEntry(order=RATING, direction=DESCENDING), SortEntry(order=SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Can this be applied on the exterior roof on a van for heat/sound? Can I topcoat this on the exterior roof with a 2 part catalyzed polyurethane based coating (ie. Raptor)? I plan to spray the entire exterior of my van with Raptor as my final top coating.

Asked by: DoItMyselfToo
As this is a super strong catalyzed product you can certainly apply to the roof of a vehicle. As for applying a bed liner over top we have never tested but it shouldn't be a problem. We recommend testing a very small batch first to ensure. Give the heat and sound barrier about an hour to flash off before top coating.
Answered by: Scott C
Date published: 2018-04-10

Can I use this to paint the bare metal ceiling of my truck ? Under the headliner.

Asked by: JimC
The sound barrier can certainly be used direct to metal.
Answered by: SeanW
Date published: 2018-04-06

Seems like a good product to apply to the inside surface of a powder coating oven to reduce the amount of heat consumed by the oven material itself. Your thoughts?

Asked by: DIY101
This would be outside our test parameters. The product is good up to 600F which is lower than cure temperatures. The only fear would be near heating elements that may be way hot and could possibly burn the material.
Answered by: S Church
Date published: 2017-07-13

Which is better put this on first of put a rubberized mat like dynamat onfirst

Asked by: Cwest
This must be the first product to go down if you wish to layer it.
Answered by: S Church
Date published: 2018-03-16

We're restoring a semi truck with plywood floorboards, will this product work on plywood?

Asked by: 80 KW
As long as the surface is properly prepped and scuffed, yes.
Answered by: KHoffnagle
Date published: 2017-12-23

Is this product epoxy, polyester, or vinyl ester resin based?

Asked by: Cassandra
This product is an Epoxy.
Answered by: S Church
Date published: 2016-12-20

Will this also act as an encapsulator?

Asked by: mccwho
This product will not act as an ecapsulator. You will want to clean down to bare metal first.
Answered by: S Church
Date published: 2017-03-30

To use this product under the car or fender wells , what would you use as a black top coat , ceramic chassis black ? Rubberized under coat ? ? 

Asked by: Pat412
You could apply the chassis black or the rubberized undercoating over top to give a nice black appearance.
Answered by: S Church
Date published: 2016-06-20
  • y_2018, m_4, d_18, h_11CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.8
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_16
  • loc_en_US, sid_15632ZP, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Eastwood Heat and Sound Barrier Coating 1.5 Gallon Kit

Item #15632ZP Brand: Eastwood

Reduce sound & heat with one easy to apply coating

In stock

Only $199.99

 

Details

Sound and heat reduction in one easy to apply coating

  • Tough 2 part catalyzed coating
  • Kit covers 30 sq.ft. at 60mil
  • Coating & activator included
  • Deadens sound & blocks heat
  • Rugged gray finish, or can be top coated
  • Resists UV, chemicals & abrasion
  • Inhibits corrosion on bare metal
  • No primer needed
  • Can be rolled on or sprayed
  • Thermally stable to 600°F

This 2 part catalyzed coating deadens sound up to 5 decibels and reduces heat up to 40F. Finally, you can improve the interior comfort of your vehicle as easily as applying paint. No primer needed, it goes on most surfaces with excellent adhesion, and protects against corrosion too. It’s perfect for floors, firewalls, and hard to reach areas. This coating can be top coated with most paints, but by itself it has a super durable gray finish that is UV, abrasion, and chemical resistant. It is even stable under heat as high as 600°F. A 1 1/2 gallon kit will cover 30 square feet to a thickness of 60mil.


More info...

About Eastwood Heat and Sound Barrier Coating 1.5 Gallon Kit

All in one product. Eastwood's heat and Sound Barrier is an all in one product. Using 2 component catalyzed chemistry this super durable can be Roll on or spray on applied. Its thermally stability is up to 600°F. Gray in color, compatible with most top coats and fortified with corrosion inhibitors. UV resistant. No primer required. Excellent adhesion, abrasion resistance, chemical resistance and film integrity. 1.5 gallon setup covers 30 square feet at 60 mil.


Contents

One US Gallon 128 Fl Oz of Part A, 2 US Quarts, 32 Fl Oz of Part B. Total 1.5 Gallons


Accessories

15549 Paint Mixing Wand
20441 undercoating Gun
51203 2.5 Quart Mixing Cups
15327 mixing Sticks
43098L Nitrile Gloves
11456 respirator
20405 Overall paint suit


Instructions

Click here for product instructions


Safety

always wear eye, skin and respiratory protection when using this product. Apply in well ventilate area away from open flame.


Warranty

Made in USA. Shelf Life: 24 months


Application

Mix 2:1 with part B. 1 Part A, 2 parts B. Pot life 2 Hours. Apply over clean surface using roller, brush of application gun. See instruction booklet, #15632Q for complete application instrcutions.


Customer Reviews

Questions & Answers

Customers also viewed: