- Pressure Blaster 150 Pound
Can I add water in this unit to keep the busy down?
There is answer to my question below but not sure if answer is yes or no. Is its manufacture product number is #4004? Answer below says same as #4004. Does it mean different product number but same as #4004 or it is #4004? Thanks.
I want to blast the outside of my log house to remove the finish. The company that supplies the finish says walnut media would probably work best. But is there another economical media that would work, without destroying the surface of the logs?
What should you use in the the first 150 dm 40004 for best results
can I use walnut shells and if so what grit.
Is this the same as ALC Deadman Abrasive Blaster — 150-Lb. Capacity, Model# 40004 ? And what media would be recommended for use on prepping outboard engines for repainting?
Can I use a high rate air compressor 17cfm diesel air compressor with this?
can you run soda in this?
Pressure Blaster 150 Pound
Pressure Blaster 150 Pound
Item #22006 Brand: ALC
With a 160-lb. media hopper this abrasive blaster has a long 70-minute blasting time.
- 70-minute blasting time
- 160-lb. media hopper
- 15 ft. 1/2"ID hose
- Blast Hood with Bump Cap
- Moisture Separator
Includes two 1/8" (15 cfm) nozzles, One 5/32" (7 cfm) nozzle, 15 ft. 1/2"ID hose, Blast Hood with Bump Cap, Moisture Separator. Wear all appropriate safety gear. Blast hoods provide NO respiratory protection. The tank is ASME certified .Be sure to wear appropriate respiratory protection.This unit requires 10 cfm @ 90 psi.
About Pressure Blaster 150 Pound
70 minute blasting time, 160 lb media hopper, Two 1/8" (15 cfm) nozzles, One 5/32" (7 cfm) nozzle, 15 ft. 1/2"ID hose, Blast Hood with Bump Cap, Moisture Separator. Wear all appropriate safety gear. Blast hoods provide NO respiratory protection. Be sure to wear appropriate respiratory protection.This unit requires 10 cfm @ 90 psi.
Consist of 2 packages: Package 1: Parts, weighs 24.28lbs, measures 18" Long, 12" Wide, 11" Deep Package 2: Tank only, weighs 52.153Lbs, measures 39" Long, 12 1/2" Wide, 14" Deep. The model 150 includes a 15' sand hose with quick disconnect, a moisture separator, 2 1/8" nozzles, and 1 5/32" nozzle, 3 seal blocks, and instructions.
Runs on as little as 7cfm @ 80 psi with the 3/32" nozzle. The included 1/8" Nozzle requires 15 cfm @ 80 psi and the included 5/32" nozzle requires 25 cfm @80 psi. Fill with screened dry media only. Pressure blasters work best when the valve at the bottom of the tank is only slightly opened. Wear appropriate safety gear. Be sure to wear an appropriate respirator. This unit requires 10 cfm @ 90 psi. Use of Walnut shell media is not recommended.
WARNING: Blasting emits abrasive under pressure. Adequate respiratory, eye, & body protection must be worn during use. Inhalation of silica particles can cause cancer & other deadly diseases. Wear NIOSH- approved respiratory protection during operation
Eastwood Offers Free Lifetime Technical Support
Attention California Residents - Proposition 65
WARNING - Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Questions & Answers
Customers also viewed:
Switch "on the fly" between soda and abrasive media...or combine!
100-lb. blaster has large, high-flow valves to speed rust/paint removalOnly $165.99
Huge 200-lb. blaster has large, high-flow valves to speed rust/paint removalOnly $238.99
50-lb. blaster has large, high-flow valves to speed rust/paint removalOnly $141.99
USA-made 2-in-1 blaster works with as little as 10 cfm at 90 psiOnly $739.99
2-in-1 blaster works with as little as 10 cfm at 90 psiOnly $213.99