• Home
  • Eastwood Professional Tubing Notcher
Eastwood Professional Tubing Notcher is rated 4.2 out of 5 by 10.
Rated 4 out of 5 by from Heavy duty tubing notcher Order # E2081777 In setup directions, page 5. It shows (1) base frame, bolt base to it with M12 bolt. The tapped hole in base frame is 10mm instead of 12mm. Location of this 10mm tapped hole is such that if I could bolt the base to base frame, the base would be even with the bottom of base frame. That puts the shaft center in the bearing block just a little less than 1.000 in. below the center of the "v" form machined in the base frame. Since I have access to machine shop equipment, I going to fix this, as I will have to drill and tap 12mm higher up, .915 inch, on base frame. Otherwise, believe it's a good tool. Like the roller bearings for the saw shaft. Bennie
Date published: 2016-02-16
Rated 5 out of 5 by from Best tubing notcher for the money. Very impressed with the quality of this unit. I've always made my notches with the lousy $36 not hers from Harbor Frieght, which wear out bushings fast and are hard to make angles with. This Eastwood unit has roller bearings to support the hole saw shaft, which should last a long time. The entire unit looks like billet steel and is very rigid. There are measurements for your different angles on the side of it. I also really like the securing mechanism for the hole saw bit. It holds the hole saw tight and true, and comes with an adaptor bushing for different brands of hole saws. My hole saws are generic Home Depot ones, and they fit great. I really believe this is the best price to quality ratio notcher you get. Thanks Eastwood!
Date published: 2016-02-15
Rated 5 out of 5 by from notcher The notcher center line with the tubing center line with the 1" tubing i was cutting didn't match up. a .060 shim fixed it. i haven't tried any other size yet. but after shimming it works awesume. would highly recommend it
Date published: 2016-06-14
  • y_2018, m_2, d_20, h_22
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_10
  • loc_en_US, sid_20447, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_eastwood

Will this tool work for sch 40 pipe? Size I’m using is 2 1/2”

Asked by: Steve
This unit will hold up to 3 inch tubing. The cutter you use will determine what it can cut through and how long it takes.
Answered by: Scott C
Date published: 2018-01-29

hello does this product works on stainless tube 3mm thickness ?

Asked by: cliff
You can certainly cut 3mm stainless tube with a good set of hole saws attached.
Answered by: Scott C
Date published: 2018-01-29

When will you have more In. Stock? 

Asked by: Marry
Next shipment due in early January 2018.
Answered by: Scott C
Date published: 2017-12-06

Can this make a round notch in the end of square tubing to make a " T "? The square tubing would be the " I " and the round would be the " -- " 

Asked by: LaneL
The problem would beholding the square stock properly without slipping. This unit is designed to hold round tubing without slipping.
Answered by: S Church
Date published: 2017-10-02

Will this unit do offset notches?

Asked by: Protocav
This unit will not be able to product offset notches.
Answered by: S Church
Date published: 2017-07-06

Hi, I'm interested in purchasing to by Eastwood Professional Tubing Notcher . do you send to Israel?

Asked by: shlomo kanyas
We do not currently ship internationally to individuals. Check out the customer service link at the bottle of the page for our list of international distributors. One may be close enough for you to work with.
Answered by: S Church
Date published: 2017-06-30

Hello. Please tell me how heavy is it.

Asked by: new hope
This item weighs about 23 lbs.
Answered by: KHoffnagle
Date published: 2017-06-14

What holds the height adjustment or is it fixed? Looks like it could move or tilt and mess up your cuts.?

Asked by: Jojo monky
The height is fixed on this unit.
Answered by: S Church
Date published: 2017-06-15
  • y_2018, m_2, d_20, h_22CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.7
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_9
  • loc_en_US, sid_20447, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Eastwood Professional Tubing Notcher

Item #20447 Brand: Eastwood

Eastwood Professional Tubing Notcher

In stock

Only $219.99



Constructed from solid steel, this easy to use tube notcher is built to perform accurate notches, time after time.

  • Create notches in 3/4" to 3" Tubing
  • Adjustable up to 50 Degrees
  • Accepts standard hole saws
  • Works with any 1/2" drill
  • Mounts in a vise or on a bench top

Designed to notch tubing from 3/4 In to 3 In tubing, which means you can build anything from a Go Cart to a 3 In exhaust on your hotrod. Use any 1/2 In hand drill to power the Eastwood Professional Tubing Notcher. Accepts all standard hole saws. Adjustable up to 50 degrees with the loosening of one bolt. Adjust to your desired angle with one hand and lock down the bearing block with your other. Easier adjustment than other designs on the market. Vise or bench top mounting.

The Eastwood Professional Tubing Notcher is designed with the professional fabricator in mind to create precision “fishmouth” notches within a wide range of angles from 90° to 140° in tubing up to 3" diameter using a hand drill with a 1/2" or larger chuck. Equipped with roller bearings and a 25 mm steel shaft, this notcher should provide years of reliable service.

More info...


Click here for product instructions


Keep fingers and hands away from moving parts while operating this tool. Always wear proper hand and eye protection when metal cutting.


90 days


20028 7 pc Hole Saw Kit
21749 Tubing Notcher Adapter


Use any 1/2 In drill to operate, accepts hole sales from 3/4 In to 3 In

Customer Reviews

Questions & Answers

Customers also viewed: