• Home
  • Shoot Suit Welded Stud Puller
Shoot Suit Welded Stud Puller is rated 4.6 out of 5 by 9.
Rated 5 out of 5 by from awesome tool............. This tool works great. Remember it is designed for smaller dimple type dents, Not big dents that are deep. For those you need the slide hammer. You will be slightly limited on your depth of dent. They need to make a couple bigger and smaller diameter bases to make it even better. As much as I like it, I do feel that being it is a screw in Access. for the standard pop rivet gun that the price is just alittle bit high, but it is worth the price still for the time it saves and added cost of bondo material saved. Now they need to have replacement part available. I am going to try to make my own sizes now. My only complaint is poor customer service and slow shipping even when paying for fast delivery.
Date published: 2014-02-09
Rated 5 out of 5 by from Fantastic Tool If you're going to buy the stud welder you've GOT TO get this tool as well. This is so much better than trying to use a slide hammer to pull dents. There's a lot more finesse with this tool. The only problem I had was I bought 2.0mm studs when I ran out and this tool slips a lot with those. You need to use the 2.5mm studs. "EZ" EZ's Customs Ringgold, GA.
Date published: 2010-01-22
Rated 5 out of 5 by from Works great! I used it on several dents on a Tahoe door and found it pulled nicely. Easy control of depth pull. I did however manage to break the plastic outer ring probably because I twisted it. I can still use it though. If the ring was steel it probably wouldn't break but would increase the cost.
Date published: 2014-02-03
  • y_2017, m_9, d_21, h_20
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_9
  • loc_en_US, sid_31014, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_eastwood

Do you sell replacement parts?

Asked by: Bsherman
We do not have any replacement parts for this tool.
Answered by: S Church
Date published: 2016-12-04

HOW LARGE A DENT CAN BE REPAIRED WITH THIS TOOL? I HAVE A PUSHED IN PANEL ABOUT 8" IN DIAMETER

Asked by: ROCCO
the inside diameter of the cone is only a little over 2" it is made for small dents.
Answered by: 1945
Date published: 2016-02-22
  • y_2017, m_9, d_21, h_20CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_2
  • loc_en_US, sid_31014, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Shoot Suit Welded Stud Puller

Item #31014 Brand: Eastwood

Pulls-out minor dings, dents precisely; works with 2.0 to 2.6mm pins

In stock

Only $37.99

Sale $34.19

Details

Shoot Suit® Stud Puller pulls-out minor dings and dents with exacting control After welding a stud onto that ding or minor dent with our stud weld gun, use the Shoot Suit® Stud Puller to pull the stud (and dent) to just the right level.
  • Use with 2.0 to 2.6mm draw pins (studs)
  • Works with any of our stud welder guns

More info...

About Shoot Suit Welded Stud Puller

Use the Shoot Suit® Stud Puller with any of our Stud Welder Systems to repair minor dings and dents due to hail, shopping carts in parking lots, etc. Just weld a draw-pin (stud) to the dinged surface, attach this tool to the pin, slowly squeeze the handles and watch as the dent is easily drawn out until it's flush with the surface. Then snip-off the draw pin. About 11-3/4" long.


Accessories

31123A Stud Pins, 2.5mm; 500-pack
31041C Stud Pins, 2.0mm; 500-pack
Stud Welder Systems


Customer Reviews

Questions & Answers

Customers also viewed: