• Home
  • Eastwood Diamond Clear Gloss for Bare Metal - Quart
Eastwood Diamond Clear Gloss for Bare Metal - Quart is rated 2.7 out of 5 by 6.
Rated 5 out of 5 by from Works Great On Brushed Metal Finish I have been using this product for over ten years. I apply it to brushed metal surfaces. It is great on stainless steel that will be outside. To prevent the stainless from picking up small bits of dissolved iron from rainwater, and spatter from the ground. Without this coating even the marine grade stainless will appear to rust. As the stainless steel is slowly coated with small bits of iron that can and will rust. It is also great on brushed aluminum, either new products or restored products. It makes 120 grit brushed aluminum look like brushed stainless steel. Sincerely, William McCormick
Date published: 2014-11-27
Rated 4 out of 5 by from a good product- aerosol isn't! I used to use the spray cans of Diamond Clear, and was frustrated at the inconsistent results. I was getting occassional fish eyes and splatter, no matter how careful I was. I even shook the cans attached to a sawzall, and warmed them up first. Never knew if I was going to have to re-do the work until I sprayed. The answer was buying it in a quart can and shooting with a cheap detail gun- never any issues now.
Date published: 2012-01-15
Rated 3 out of 5 by from difficult to poor out of can We have been using this product for about 10 years. We are satisfied with the product however the can is not designed well to pour out of it. The can used to come with a screw on lid which made for easy pouring and less spillage. Wish they would go back to the screw on lid!!
Date published: 2015-10-10
  • y_2017, m_11, d_18, h_1
  • bvseo_bulk, prod_bvrr, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_6
  • loc_en_US, sid_10357ZP, prod, sort_[SortEntry(order=RELEVANCE, direction=DESCENDING)]
  • clientName_eastwood

Is this product compatible with Flood Penetrol additive?

Asked by: doctoma106
We have never tested any of our products with such an additive.
Answered by: S Church
Date published: 2017-10-08

i was wondering if this product would work in a dump truck bed that hauls asphalt

Asked by: joe15
This product would get destroyed in a dump truck. Your best bet would be to try a bed liner.
Answered by: S Church
Date published: 2017-08-29

Could I use this for a bare metal car? To give it that ratrod look, but not have any problems with surface rust. Seeing as I love in Kentucky we have some heavy winters 

Asked by: Leeblaze
It would be possible to use this product for a bare car, but the best and newest product out is our "Exo-Armour". That product will not change to look of the metal or add a glossy appearance. It isn’t affected by solvents or chemicals and passed the 4000 hour of salt spray resistance test. Just remember to thoroughly clean the surfaces to be covered with our "Pre" wax and grease remover for the best results.
Answered by: S Church
Date published: 2015-06-03

How about use on airstream, either polished or not polished for a clear coat

Asked by: David1
The best and most durable clear for bare metal (polished or not) would be our Exo Armour. http://www.eastwood.com/exoarmour.html
Answered by: SeanA
Date published: 2014-12-19
  • y_2017, m_11, d_18, h_1CST
  • bvseo_bulk, prod_bvqa, vn_bulk_2.0.3
  • cp_1, bvpage1
  • co_hasquestionsanswers, tq_4
  • loc_en_US, sid_10357ZP, prod, sort_[SortEntry(order=LAST_APPROVED_ANSWER_SUBMISSION_TIME, direction=DESCENDING)]
  • clientName_eastwood

Eastwood Diamond Clear Gloss for Bare Metal - Quart

Item #10357ZP

Self-leveling formula resists chips, cracks, fading and yellowing

In stock

Only $30.99

Details

Protect metal parts with a crystal clear, tough, flexible coating that keeps brass, aluminum, steel, die-cast, even cast iron looking great. This self-leveling formulation, resists chips, cracks, fading and yellowing. May slightly dull reflectivity. Resists fuels and temps up to 300 degrees. Ideal in underhood applications except exhaust manifolds. Great for polished wheels, aluminum valve covers as well as items around the shop and home. One quart of Diamond Clear for Bare Metal covers about 40 sq.ft. Assure surface is grease and oil free with PRE Painting Prep (10041Z).

More info...

About Eastwood Diamond Clear Gloss for Bare Metal - Quart

Protect metal parts with a crystal clear, tough, flexible coating that keeps brass, aluminum, steel, die-cast, even cast iron looking great. This self- leveling formulation, resists chips, cracks, fading and yellowing. May slightly dull reflectivity. Resists fuels and temps up to 300 degrees. Ideal in underhood applications except exhaust manifolds. Great for polished wheels, aluminum valve covers as well as items around the shop and home. One quart of Diamond Clear for Bare Metal covers about 40 sq.ft. Assure surface is grease and oil free with PRE Painting Prep (10041Z).


MSDS Sheet

Click Here for Material Safety Data Sheet


Instructions

Click here for product instructions


Warranty

QUANTITY DISCOUNTS AVAILABLE FOR THIS ITEM


Customer Reviews

Questions & Answers