• Home
  • Eastwood Diamond Clear Satin for Bare Metal 11oz Aerosol
Eastwood Diamond Clear Satin/Metal Surfaces Aerosol 11 oz. is rated 4.444444444444445 out of 5 by 9.
Rated 5 out of 5 by from diamond clear for bare metals caution I polished the outer edge of my aluminum rims and painted the insides. I used Diamond Clear Satin for painted surfaces on that, after taping off the polished part. Then I taped off carefully the painted part and applied Diamond Clear Satin for bare metals. It looked great, but there were a few places where the bare metal clear had run down onto the clearcoated painted part and immediately the paint began to bubble and soften and I had to strip the whole wheel and re-do. So DO NOT get any of the bare metal primer onto the painted surface primer! Otherwise a good product that has a good, smooth flow.
Date published: 2012-07-16
Rated 5 out of 5 by from Applied to raw brushed aluminum It laid down smooth and level. The finish was a satin brushed look that I was expecting.
Date published: 2013-05-21
Rated 5 out of 5 by from Highly Recommend This is a re-order of several cans I have already gone through. I would highly recommend this product!
Date published: 2014-04-07
Rated 3 out of 5 by from Bad for my parts but could be good for others Followed directions,went on nice and looked great. After a day and a half drying I bumped an edge and found out you can take it right off with your finger nail. Luckily it came off with lacquer thinner and didn't even need to be rebuffed. I wanted to use the clear on Corvette suspension parts, bad idea. If you would use this for a part that will not get nicked or chipped, like inside, it would be fine.
Date published: 2012-08-15
Rated 5 out of 5 by from nice product, easy to use and nice finnish I have used this on bare metal to "seal" it in to avoid rust. It does a great job. The sheen was perfect so as it was not glossy. I sprayed it on my cast brake rotors and the cast master cylinder to add life to the part without it turning rusty. It went on smooth and I followed the directions to a T. I also used the clear for the painted surfaces with the same success as well..
Date published: 2011-04-11
Rated 4 out of 5 by from satin clear Good product! You can also go to the local hardware and get satin clear in a larger can for about half the cost. Just be sure it is fuel resistant if you are using it on an intake manifold.
Date published: 2016-08-16
Rated 5 out of 5 by from Not just for working on cars... I used this product for a craft project I was working on. I needed something durable that would cover bare metal & had a satin finish. This worked great.
Date published: 2013-07-02
Rated 3 out of 5 by from diamond clear spray cans i used it on both wet paint and bare metal with good success. does not stick well to smooth surfaces. had problems with polished aluminum wheels too.
Date published: 2012-11-10
  • 2016-09-28T07:48CST
  • bvseo_cps, prod_bvrr, vn_cps_3.4.0
  • cp_1, bvpage1
  • co_hasreviews, tv_0, tr_9
  • loc_en_US, sid_10300Z, PRD, sort_relevancy
  • clientName_eastwood

Eastwood Diamond Clear Satin for Bare Metal 11oz Aerosol

Item #10300Z

Tough, flexible, clear satin barrier keeps metal looking bright


Diamond Clear™ Satin for Bare Metal coats metal parts with an invisible barrier that keeps metal looking bright

  • Resists chips, cracks, fading and yellowing
  • Spray on polished wheels, aluminum valve covers, underhood parts
  • Fuel-resistant; heat-resistant to 300 degreesF

Your vehicle's brass, aluminum, steel, die-cast, even cast iron parts can look their absolute best when you spray-on this clear, tough, flexible, Diamond Clear™ Satin coating.

More info...

About Eastwood Diamond Clear Satin for Bare Metal 11oz Aerosol

Diamond Clear Satin for Bare Metal - Delivering the same durable protection with clarity as our High Gloss version; Eastwood is pleased to announce this new addition to our line of Diamond Clear products. We've responded to your requests to deliver a durable coating that protects while presenting a bare metal appearance. This new coating resists temperatures up to 300 degrees F. Great for providing an invisible protective barrier to aluminum manifolds, cast alloy valve covers, distributor and alternator housings and more. Net contents 11 ozs. Covers up to 6 Sq. Ft.


One 11 oz. net wt. aerosol, enough to cover up to 6 square feet.


Click here for product instructions




For use on aluminum, steel, brass, cast iron, and pot metal for long term protection. Clean part thoroughly before coating. Use when can and surface to be coated are between 70-90 degrees F. For best protection make sure complete coverage has been achieved. Apply even overlapping strokes with can about 12" from the surface. Allow 15 minutes between coats if additional coats are desired. Allow surface to dry 24 hours before handling. See can label for additional information .

Customers also viewed: