SAVE HUNDREDS with this awesome combo deal. You can finally start serious fabrication at an incredible price! TIG weld steel, stainless and aluminum today and also cut metal up to 7/8" thick with this amazing deal that combines the popular TIG AC/DC and Versa-Cut 60 Plasma Cutter. Plus both units operate on either 120V or 240V and are backed by the Eastwood 3 Year Warranty.

The Eastwood TIG 200 AC/DC Features:

• Operates on either 110vAC, 15-amp circuit or 220vAC, 30-amp circuit.
• 1/4"-thick welding capacity on 220VAC.
• High-frequency start for precise arc control.
• Rocker Style Foot Pedal
• Gas FlowMeter
• Flex Head Torch
• Gas Lens Kit
• Square-wave inverter for accurate aluminum welding.
• Flex Head WP-17-type torch accepts common cups and collets with up to 1/8" electrodes.
• Gas lens kit will greatly improve your fabrication skills.
• Rocker Style foot pedal with machine mounted controls to improve your precision.
• Flow Meter Gauge for improved gas flow control with quick, repeatable flow adjustment.
• TIG Welding AC Duty Cycle (%): 120VAC 60% at 145 amps, 220VAC 60% at 190 amps)
• Stick Welding Feature - welds in AC and DC Positive/Negative.
• Includes long torch and ground cables so you can easily move around your project.

Versa Cut 60 Plasma Cutter

Quickly and precisely carve all types of metal as well as body panels and more with this heavy-duty Eastwood plasma cutter. The adjustable 60-amp output and Trafimet CB70 torch can cut through metal ranging from 24-gauge sheet metal to thick 7/8 inch plates. Use it on mild steel, stainless and aluminum in your shop or at a worksite.

The Eastwood Versa Cut 60 Plasma Cutter Features:

• 120 or 240 Volts AC input
• Cuts thin sheet metal to thick 7/8" thick plate (cuts 3/16" on 120 VAC)
• Digital amperage readout for increased precision
• Long 20' torch cable and 10' ground cable with clamp
• Rated 60 amp output on 240 VAC; 30 amp on 120 VAC
• Lightweight and Portable - only 31 lbs!
• 2T/4T Torch Mode for smoother long cuts
• Durable Duty Cycle of 60% @ 60 amps on 240v and 60% @ 30 amps on 120v
• Uses common consumables that are available at Eastwood or most welding supply stores

**Note: Due to the High Frequency start feature, we do not recommend using this machine on a CNC plasma table.**

This unit comes with a heavy-duty IGBT inverter, internal moisture separator, long cables and adjustable air pressure regulator assuring long life and accurate cuts. It also includes a self-starting arc which helps in areas where rust and contaminants may be an issue. It has a duty cycle of 60 percent for long continuous cuts. At only 31 pounds, it is light enough to bring to a friend's shop, a race track or any place metal needs to be cut.

TIG 200 AC/DC Specifications

Duty Cycle

The Rated Duty Cycle refers to the amount of welding that can be done within an amount of time. The Eastwood TIG 200 has a duty cycle of 60% at 190 Amps. It is easiest to look at your welding time in blocks of 10 Minutes and the Duty Cycle being a percentage of that 10 Minutes. If welding at 190 Amps with a 60% Duty Cycle, within a 10 Minute block of time you can weld for 6 Minutes with 4 Minutes of cooling for the welder. To increase the Duty Cycle you can turn down the Amperage Output control. Going above 190 Amps will yield a lower duty cycle.

Versa-Cut 60 Specifications

• TIG 200 AC/DC Welder with NEMA6-50P Plug
• (1) Shielding Gas Flow Meter / Regulator
• (1) Shielding Gas Hose (4.6’)
• (1) Ground Cable with Clamp (9.5’)
• (1) Flex Head TIG Torch (17 Series) which accepts industry standard cups, collets and collet bodies (12' Torch Cable)
• (1) Rocker Style Foot Pedal for Amperage Control (16’ Cable)
• (1) 110-120 VAC to 220-240 VAC Adapter Plug
• (1) Instruction Manual
• (1) Hand Held Shield
• (1) Hammer/Brush
• (1) #8 Gas Lens
• (1) Long Back Cap
• (1) 3/32” Collet Body (Installed)
• (1) 3/32” Collet (Installed)
• (1) 3/32” x 6” Red Thoriated Tungsten
• (1) 3/32” x 6” Green Pure Tungsten

• Versa-Cut 60 Amp Plasma Cutter
• (1) Trafimet CB70 Torch and 20’ Supply Line
• (1) 10’ Ground Lead and Clamp
• (1) NEMA5-15P to NEMA 6-50R, 2' (240v to 120v Cable)
• (1) Torch Flow Tester
• (1) Electrode Wrench
• (1) Replacement Electrode
• (1) Replacement Nozzle
• (1) Instruction Manual

Click here for TIG product instructions

Click here for Plasma Cutter product instructions