- Rust Encapsulator Gray 15 ounce Aerosol
What temperature will this withstand?
Can I use PQR15 Cleaner/Degreaser first before applying Rust Encapsulator? Are these products compatible. If yes, after applying Degreaser, do I then apply Encapsulator directly or some additional prep needed? Does Encapsulator come in any blue colors?
I have a 57 Chevy with the original factory rust proofing sprayed in the wheel tubs and bottom of the car. Needless to say this is extremely hard to remove and is unsightly, can this be used to cover the old rust proofing or is there a better option?
I have a Eastwood SCT and I am planing to remove as much rust with it as possible then encapsulate in case I did not remove everything then paint on top of it. Is this good idea or should I use the SCT then use primer instead of encapsulating?
Can this be used directly over rust on car exhaust manifold and for the entire exhaust up to the rear muffler? and is there a need to paint over it?
does this come in quarts?..................thanks joe
I have a satellite dish. It has surface rust. Can it be used on this item? Also, at what temperature can it be applied and how long does it take to cure?
I want to spray for rust in the front door posts of a 1964 GMC after I peel the roof. Will the 360 degree extension fit other cans of rust preventers?
Rust Encapsulator Gray 15 ounce Aerosol
Item #14822Z Brand: Eastwood
Stop rust in its tracks! Our Rust Encapsulator (Gray) has been reformulated with TWICE the corrosion resistance!
- Gray in color
- Twice the corrosion resistance of our original formula for greater durability (tested to 500 hours in a salt-spray chamber)
- Epoxy-fortified for better adhesion and topcoat compatibility
- Penetrates deeper to prevent rust from spreading or forming, even in hard-to-reach areas
- Cures faster, and the low-VOC formula is acceptable in California
- 15-oz. aerosol covers about 10 sq. ft.
- As seen on "My Classic Car" TV show
You thought it was good before...wait ’til you try this Rust Encapsulator! It seals and stops rust and corrosion from spreading, but it performs even better than our original formula. Tested against well-known brands, the Eastwood Rust Encapsulator has proven to be superior in sunlight resistance, preventing rust creep, and overall durability.
Unlike off the shelf under coatings, Rubberized Rust Encapsulator can be applied directly over rust and without the bubbling that creates air pockets thus trapping rust. Since its engineered with high tech flex agents, its pliable finish protects surfaces from abrasions, road hazards and deadens sound. So durable it exceeded 1,000 hours of salt spray chamber testing, this surpasses the standards for a 2 component catalyzed coating! Simply apply directly over rust or bare metal; no need to topcoat. Remains flexible and durable. Satin gray finish.
Net Weight 15 ounces
SAS Bandit Respirator
10041Z PRE Painting Prep
16060Z Rust Encapsulator
51483Z Rust Converter, Aerosol
12515Z Internal Frame Coating
11175Z Extreme Chassis Black
10025Z Original Chassis Black
10020Z Silver Exhaust System Paint
Use a wire brush to remove loose rust, scale and paint, and remove dust, grease and oil deposits. Feather surrounding paint with 220-grit sandpaper. Shake can for at least 2 minutes once the mixing ball starts to rattle. Hold the Rust Encapsulator can 10-12" above surface as you spray. A single coat dries to the touch in 20 minutes, and is thoroughly dry in 3-4 hours at 68°F. For greater durability, a second coat can be applied 1 hour after the first. Allow 6-8 hours after the last coat before applying topcoat. Use over or under body fillers.
always wear eye, skin and respirtaory protection. Apply in a well ventilated area away from open flame.
Made in USA
Wire Brush to remove loose rust, scale and paint. Remove dust, grease, oil deposits. Shake can for at least 2 mins after mixing ball starts to rattle.Feather surrounding paint with 220 grit sandpaper. Apply Rust Encapsulatorcan 10 to 12 inches from surface. Single coats dry to the touch in 20 minutes and arethoroughly dry in 3 to 4 hours at 68 degrees F. For greater durability a second coat can be applied one hour after the first. Allow 6 to 8 hours after last coat before applying top coat.
Questions & Answers
Customers also viewed:
High-grade patina preserving coat prevents further discoloration and protects surfaces from corrosion
Stop rust in its tracks! Superior UV Resistance and Convenient Spray Aerosol or Brushable Quarts & Gallons
Starting at: $14.97
Stops rust, and protects the underside of your car!
Starting at: $18.97
Transforms surface rust into a paintable surface!
Starting at: $15.97