Item #
21116
BRAND: Eastwood
Tubing Bender Stand
Use this Stand for with the High Capacity Tubing Bender
Use this Stand for with the High Capacity Tubing Bender
Tubing Bender Stand is rated
out of
5 by
29.
Use this Stand for with the High Capacity Tubing Bender
90 day Warranty Included
100% Satisfaction Guarantee Since 1978
We stand behind our solutions and customers.
- • 90 Day Returns
- • Lifetime Tech Support
Frequently Bought Together
Price for all checked items:
Product Overview:
Description
Stand for the Eastwood High Capacity Tubing Bender that can be mounted into a shop floor.
Warranty
In the Box
Contents
Guides & Accessories
Safety Information
Accessories
21117 0.75" x 3" Radius, 120° Die
21118 1.0" x 4" Radius, 120° Die
21119 1.5" x 5" Radius, 120° Die
21120 1.625" x 5" Radius, 120° Die
21121 1.75" x 6" Radius, 120° Die
21122 2" x 6" Radius, 120° Die
21123 0.75" x 3" Radius, 240° Die
21124 1.0" x 4" Radius, 240° Die
21125 1.5" x 5" Radius, 240° Die
21126 1.625" x 5" Radius, 240° Die
21127 1.75" x 6" Radius, 240° Die
Application Tips
Easy To Store When Not In Use
Reviews
Rated 5 out of
5
by
Dave I upstate New York from
Eastwood tubing bender and dies
The new die set should work as well as the previous sets. The machining is good and the die parts fit the bender as designed.
Date published: 2024-10-03
Rated 5 out of
5
by
RyDaddy from
Whole roll cage built with minimal issues
I did have an issue with a bend pin, but Eastwood remedied that quickly.
Date published: 2023-03-05
Rated 5 out of
5
by
RyDaddy from
Nice Unit
I need to fight the pin out of the saddle to get the bent tube out, but I figured out a technique to make it work. Probably just that I am using it at its limit on 2" x .120-wall tube.
Date published: 2023-03-05
Rated 5 out of
5
by
Anonymous from
Fits the Woodward WFB2
Bought this to find out if the Woodward Fab and Eastwood tube bending dies were interchangeable. The answer is yes. These dies fit the Woodward Fab WFB2 bender.
Read the other reviews and I can tell you the one where the holding clamp got bent was operator error. If you use the shortest pin it doesn't seat far enough and the bottom will slip off. So make sure you use the correct pin.
Date published: 2020-02-20
Rated 5 out of
5
by
Anonymous from
It Fits WFB2
Bought this die to figure out once and for all if the Woodward Fab and Eastwood tubing dies were interchangeable. The answer is YES THESE DIES WILL FIT THE WFB2 tubing bender as well.
Date published: 2020-02-20
Rated 5 out of
5
by
Tony from
advice for soft tubing
Reading through the reviews I see many questions about bending aluminum and kinking issues. The trick to bending soft materials with any bender is to cap one end of the tube, fill it with sand, then cap the final end. The sand will go around the bend and support the tube from the inside.
Date published: 2019-06-23
Questions & Answers
How would you remove the material after you bent it to 240°?
you can tap the tubing off the tool by using a rubber or wooden mallet.
Date published: 2023-05-06
Does the 120 degree die work differently than the 240 and how? Tnx
The die does not operate any differently, but you will be limited to 120° or 240° maximum bends. If you need more than 120° of angle definitely go with a 240° die.
Date published: 2022-05-26
Do you have a 1 1/4, die for tubing bender?
We do not have a 1.25" die for this bender at this moment
Date published: 2022-05-12
I can bend pipe 1-1/4 sch40. Normally what I work are railings.
We do not offer a 1 1/4" die at the moment
Date published: 2024-02-09
Will this bender work to bend EMT conduit if you use the correct die? I need to bend 1.25" EMT conduit, the OD is 1.50 and the wall thickness is .072
We do not recommend using this tool to bend EMT conduit.
Date published: 2024-02-09
Can the bender bend 1 1/4 dom tube
We do not currently have a 1 1/4" die for this machine at this time.
Date published: 2021-06-08
Is the a die set to bend for square tubing?
This is for round tubing only. Unfortunately, we do not currently offer any dies for square tubing.
Date published: 2024-02-09
Will these work on a pro 105 bender
The 1.75in X 6in Radius 240 degree Die(21127) is specified for the Eastwood High Capacity Tubing Bender (21115). As we do not have cross reference material we can not determine if it will fit your bender, You may want to call the manufacturer of your bender for specifications and details.
Date published: 2021-01-25
We found other products you might like!
Tubing Bender Stand
Reg.
$132.99
Sale
$69.97
Save
$63.02
In Stock