
Details
Eastwood Spruce Green Metallic - This medium green has plenty of blue shading and a nice metallic effect.
Eastwood's premium Single-Stage Acrylic Urethane Topcoat provides exceptional long-lasting beauty and durability.
- Catalyzed urethane for unsurpassed durability
- Highly resistant to UV rays, chemicals, chips
- Makes 1 sprayable gallon when mixed 3:1 with a required activator
- Approximate coverage: 125 SQ FT
- Flake/Pearl Particle size: 10-25 microns
- Max Temperature: Paint will handle up to 300 degrees without delamination, but color shift may occur, so it should not be used in a high heat setting
- Made in the USA
This premium 2-component topcoat system is blended with top-quality raw materials and advanced composition coatings technology. Superior to acrylic, alkyd and lacquer coatings. Eastwood's single-stage urethane paints hold their gloss longer and won't yellow.
Specifications
SINGLE-STAGE PAINT MIXING RATIOS
Thoroughly mix three parts single-stage urethane paint with one part Activator. No additional reduction is required but can be used as needed.
Use caution in mixing materials as Eastwood’s single-stage urethane paint may begin to gel after approximately two hours (at 70 °F).
PAINT GUN SET-UP
HVLP Gun: Fluid Tip 1.3-1.5 mm Inlet Spray Pressure 25-30 psi
Conventional Gravity: Fluid Tip 1.3-1.6 mm Inlet Spray Pressure 45-50 psi
Conventional Siphon: Fluid Tip: 1.4-1.8 mm Inlet Spray Pressure 45-50 psi
APPLICATION INSTRUCTIONS
Apply single-stage urethane paints in two to three medium wet coats as necessary to
achieve sufficient coverage, allowing ten minute flash between coats. Additional coats
may be necessary to achieve total coverage for some metallic colors. A final “fog coat”
may be applied with metallic colors to help set an even flake pattern and /or adjust flake
orientation. A dry film thickness of approximately 2 mil is recommended. Paint should be
dust free within 10-15 minutes and tack-free within one hour (at 70 °F). Re-coat anytime
after the previous coat has flashed, or before 18 hours. After 18 hours, paint should be
abraded prior to re-coating for proper adhesion purposes.
This urethane paint may be applied as a stand-alone single-stage system, or in combination
with Eastwood’s High Solids Urethane Clear as a basecoat/clearcoat system. Additionally,
Urethane Clear may be integrated into Urethane color. When combining the two
systems, be sure to activate each side (the paint and the clear) separately, with their own
activators at the correct mix ratios, before blending.
When used as a Single-Stage Urethane Paint, this coating may be wet-sanded and polished
for increased depth and gloss like any other urethane topcoat. Care should be
taken when lightly cutting metallic colors to prevent disturbing aluminum flake.
Safety
Always wear proper eye, skin and respiratory protection. Always paint in a well-ventilated area away from sparks and open flame. Consult MSDS and product data sheets for proper safety precautions.
FAQs
(Q) Do I need a clear?
(A) No, but you should use a clearcoat over metallics.
(Q) How much paint do I need?
(A) Typically one gallon per car. If you are also painting jambs, under the hood, or the trunk, use 2 gallons. For large cars and pickup trucks, use 2 gallons. Number of coats, prep and application methods will affect the amount of paint required.
Accessories
PRE Painting Prep
Concours HVLP Paint Guns
Air Filters and Dryers
6" Liquid Ice Buffing Kit
Epoxy Primers
Urethane Primers
Polyester Primers
Clear Coats
Eastwood Offers Free Lifetime Technical Support
Click here for product SDS information
Attention California Residents - Proposition 65

Customer Reviews
Questions & Answers
You may also be interested in the following product(s)
-
Eastwood Midnight Metallic Black 3:1 Single Stage Paint
Starting at: $127.98
-
Eastwood Dead Rat Flat Black 3:1 Single Stage Paint
Starting at: $126.98
-
Eastwood Boulevard Black 3:1 Single Stage Paint
Starting at: $116.98
-
Eastwood Black Epoxy Primer and Activator Quarts
Starting at: $47.98
-
2K Aerospray Rat Rod Satin Black
$27.99