
Details
Contour® Sprayable High-Build Primer/Surfacer serves as an excellent base for any paint system
- High-Build With Excellent Filling Capabilities
- Easy To Sand With No Shrinkage
- Excellent Adhesion To Metals, Fiberglass, and Body Fillers
- Includes hardener
- Application: 8 mils wet = 4-6 mils dry. 10 mils wet = 6-8 mils dry.
2-component polyester primer/surfacer has excellent filling characteristics and superior adhesion to steel, aluminum, fiberglass, SMC, OE finishes, self-etching primers and body fillers.
Contents
Contour® Sprayable Polyester Primer-Surfacer/Gray, Qt.
(1) 1 oz tube of Liquid Hardener
Contour® Sprayable Polyester Primer-Surfacer/Gray, Gal.
(2) 2 oz tubes of Liquid Hardener
Application
SURFACE PREPARATION:
1. Surface must be clean and free of wax, grease and debris. Use Eastwood’s PRE Painting
Prep to remove all contaminants.
2. Sand/abrade surface
A. Body Filler & Putty: Rough sand with 80 grit, then 180-220 and featheredge with 320 grit
B. Untreated Steel, Galvanized and Aluminum: Sand with 80-180 grit
C. Painted Surfaces: Sand and featheredge using 80, 180 ,220 and finish with 320 grit.
3. Completely final sand surface with 320-400 grit paper and re-clean with PRE Painting Prep
MIX: 2% by weight; 2.56 oz per Gallon; .64 oz per Quart
SPRAY GUN & APPLICATION RECOMMENDATIONS:
1.8mm to 2.5mm Fluid Tip Size, 35 to 40 PSI
Apply two or three medium wet coats as needed. Heavy wet coats should NOT be applied.
Dry spray may be removed be for recoating. Allow 90 minutes dry time before sanding at 68°F
(20°C). Finish with 220 grit followed by 320-400 grit
DRY TIMES AT 68°F (20°C)
Flash: 5-10 minutes
To Sand: 90 minutes, over self etching primer: 4-6 hours
To Topcoat: 90 minutes, over self-etching primer: 4-6 hours
Force Dry: Purge 10 minutes, Bake: 30 minutes at 140°F (60°C)
Pot Life: 30 minutes at 68°F (20°C). If needed add 5-10% acetone to extend pot life.
Clean equipment with lacquer thinner immediately after use.
This product is not meant for use below 60°F (16°C), dry time and performance will be dramatically
affected.
CAUTION: DO NOT return catalyzed material back into can. To avoid
contamination, seal lid tightly after each use. Store in a cool dry place.

Accessories
13919 Eastwood Filler Spreaders
31273 Eastwood Filler Mixing Board
10041Z PRE Painting Prep
31160 Dura-Block Sanding Blocks
21538 Larry Lyles "Basic Body Repair" DVD
Eastwood Dual Action Palm Sander
43120 Eastwood Fender Stand
12416Z Eastwood Guide Coat, Black
Safety
Always wear eye, skin and respiratory protection when using this product. Always apply in a well-ventilated area. Consult MSDS and product label for specific safety warnings.
Eastwood Offers Free Lifetime Technical Support
Click here for product SDS information
Attention California Residents - Proposition 65

Customer Reviews
Questions & Answers
You may also be interested in the following product(s)
-
Eastwood 2K 4:1 Urethane Primer Activator Quart
$34.99 -
2K Aerospray High Build Urethane Primer Gray & Black
Starting at: $27.99
-
Eastwood Black Epoxy Primer and Activator Quarts
Starting at: $47.98
-
Eastwood Gray Epoxy Primer and Activator Quarts
Starting at: $44.98
-
Eastwood CONTOUR® Light Weight Short Strand Body Filler 3L
$55.99